RCA 26930 User Manual download pdf (Page 2)

CHANGING A STORED NUMBER

Use the same procedure to change a stored number as you

do to store a number—you’re just replacing the phone

number with a different one.

DIALING A STORED NUMBER

1. Make sure the phone is ON by pressing the TALK button.

2. Press MEMORY.

3. Press the number (0-9) for the desired memory location.

The number dials automatically.

- OR -

1. Make sure the phone is OFF.

2. Press MEMORY.

3. Use the arrow buttons to scroll through the numbers

stored in memory until the desired number is shown.

4. Press CALL BACK. The numbers dials automatically.

IMPORTANT: If you make test calls to emergency

numbers stored in memory, remain on the line and

briefly explain the reason for the call to the dispatcher.

Also, it’s a good idea to make these calls in off-peak

hours, such as early morning or late evening.

INSERTING A PAUSE IN THE DIALING

SEQUENCE

Press the REDIAL button to insert a delay in the dialing

sequence of a stored telephone number when a pause is

needed to wait for a dial tone (for example after you dial 9

for an outside line, or to wait for a computer access tone).

Each pause counts as 1 digit in the dialing sequence.

REVIEWING AND DELETING STORED

NUMBERS

1. Press MEMORY, then use the arrow keys to view the entry.

2. While the entry is displayed, press DELETE to delete the

entry. The display shows

ERASE MEMO?

3. Press DELETE a second time to delete the entry.

CHAIN DIALING FROM MEMORY

Use this feature to make calls which require a sequence of

numbers such as using a calling card for a frequently

called long distance number. Basically, you dial each part

of the sequence from memory. The following example

shows how you can use chain dialing to make a call

through a long distance service:

The Number For Memory Location

Long distance access number 7

Authorization code 8

Frequently called long distance number 9

1. Make sure the phone is ON.

2. Press MEMORY and then press 7.

3. When you hear the access tone, press MEMORY and

then press 8.

4. At the next access tone, press MEMORY and then 9.

TIP: Wait for the access tones before pressing the next

memory button, or your call might not go through.

HEADSET AND BELT CLIP

OPERATION

CONNECTING A HEADSET TO THE

HANDSET

For hands free

conversation, connect the

headset (optional) to the

HEADSET jack as shown.

The handset receiver and

microphone are disabled

when the headset is

connected.

Adjust the headset to rest

comfortably on top of your

head and over your ear.

Move the microphone to

approximately 2 to 3 inches

from your mouth.

• Press the TALK button to

answer or place a call

before using the headset.

CONNECTING THE BELT CLIP

There are two slots, one on

each side of the handset.

• Attach the belt clip by

inserting the sides of the

belt clip into the slots.

Snap the ends of the belt

clip into place.

CHANGING THE BATTERY

Make sure the telephone is OFF before you replace

battery.

1. Remove the battery compartment door.

2. Disconnect the cord attached to

the battery pack and remove the

battery pack from the handset.

3. Insert the new battery pack and

connect the cord into the jack

inside the handset.

4. Put the battery compartment door

back on.

5. Place handset in the base to

charge. If you don’t charge the

handset battery properly (for 12 hours)

when you first set up the phone and/or

when you install a new battery pack,

the battery’s long-term performance

will be compromised.

BATTERY SAFETY PRECAUTIONS

• Do not burn, disassemble, mutilate, or puncture. Like

other batteries of this type, toxic materials could be

released which can cause injury.

• To reduce the risk of fire or personal injury, use only the

battery listed in the User’s Guide.

• Keep batteries out of the reach of children.

• Remove batteries if storing over 30 days.

Ni-Cd

RBRC

GENERAL PRODUCT CARE

To keep your telephone working and looking good, follow

these guidelines:

• Avoid putting the phone near heating appliances and

devices that generate electrical noise (for example,

motors or fluorescent lamps).

• DO NOT expose to direct sunlight or moisture.

• Avoid dropping the handset, as well as other rough

treatment to the phone.

• Clean the phone with a soft cloth.

• Never use a strong cleaning agent or abrasive powder

because this will damage the finish.

• Retain the original packaging in case you need to ship

the phone at a later date.

• Periodically clean the charge contacts on the handset

and base with a clean pencil eraser.

CAUSES OF POOR RECEPTION

• Aluminum siding

• Foil backing on insulation

• Heating ducts and other metal construction can shield

radio signals

• You’re too close to appliances such as microwaves,

stoves, computers, etc.

• Atmospheric conditions, such as strong storms

• Base is installed in the basement or lower floor of the house

• Base is plugged into an AC outlet with other electronic devices

• Baby monitor is using the same frequency

• Handset battery is low.

• You’re out of range of the base.

MESSAGE INDICATORS

The following indicators show the status of a

message or of the unit.

ERROR Caller information has been interrupted

during transmission or the phone is

excessively noisy.

ENTER NAME Prompt telling you to enter a name for

one of the 10 memory locations.

ERASE ALL? Prompt asking if you want to erase all

Caller ID records.

ERASE CALL ID? Prompt asking if you want to erase the

current Caller ID record that is shown

on the display.

ERASE MEMO? Prompt asking if you want to erase one

of the 10 numbers stored in the

phone's outgoing memory.

END OF LIST Indicates there is no additional

information in the Caller ID memory log.

NEW Indicates call or calls have not been

reviewed.

UNKNOWN The incoming call is from an area not

serviced by Caller ID or the information

was not sent.

PAGING YOU Someone has pressed the PAGE button

on the base.

BLOCKED The person is calling from a number that

has been blocked from transmission.

REPT Repeat call message. Indicates that a

new call from the same number was

received more than once.

NO DATA No Caller ID information was received.

ANDSET

OUND

IGNALS

Signal Meaning

A long warbling tone Signals an incoming call

(with ringer on)

One short beep, one Page signal

long beep (several times)

Three short beeps Out of range

Four short beeps Low battery warning

TROUBLESHOOTING TIPS

CALLER ID

Problem Solution

No Display • Is battery fully charged? Try

replacing the battery.

• If you are using AC power,

make sure that the unit is

connected to a non-switched

electrical outlet. Disconnect

the unit from the plug and

plug it in again.

• Did you order Caller ID

service from your local

telephone company?

Caller ID Error Message • The unit displays this

message if it detects

anything other than valid

Caller ID information during

the silent period after the

first ring. This message

indicates the presence of

noise on the line.

TELEPHONE

Problem Solution

No dial tone • Check installation:

— Is the base power cord

connected to a working outlet?

— Is the telephone line cord

connected to the base unit

and the wall jack?

• Disconnect the base from

the wall jack and connect

another phone to the same

jack. If there is no dial tone

in the second phone, the

problem might be your

wiring or local service.

• Is the handset out of range

of the base?

• Make sure the battery is

properly charged (12 hours).

• Is the battery pack

installed correctly?

• Did the handset beep

when you pressed the

TALK button? Did the

CHARGE/ IN USE indicator

come on? The battery may

need to be charged.

TELEPHONE

Problem Solution

Dial tone is OK, but • Make sure the tone/

can't dial out pulse setting is programmed

correctly.

Handset does not ring • Make sure the RINGER

switch on the handset is

turned to ON.

• You may have too many

extension phones on your line.

Try unplugging some phones.

• See solutions for “No dial tone.”

You experience static, • Change channels

noise, or fading in • Is handset out of range?

and out Move closer to the base.

• Does the base need to be

relocated?

• Charge battery.

• Make sure base is not

plugged into an outlet with

another household

appliance.

Unit beeps • Place handset in base for

20 seconds to reset the

security code. If that

doesn’t work, charge

battery for 12 hours.

• Clean charging contacts on

handset and base with a

soft cloth, or an eraser.

• See solutions for “No dial tone.”

• Replace battery.

Memory Dialing • Did you program the memory

location keys correctly?

• Did you follow proper

dialing sequence?

• Make sure the tone/pulse

setting is programmed correctly.

• Did you reprogram

numbers into memory

after power outage or

battery replacement?

ERVICE

The FCC requires this product to be serviced only by the

manufacturer or its authorized service agents. In

accordance with FCC requirements, changes or

modifications not expressly approved by ATLINKS USA,

Inc. could void the user’s authority to operate this product.

For instructions on how to obtain service, refer to the

warranty included in this user's guide or contact Consumer

Information at 1-800-448-0329.

Or refer inquiries to:

ATLINKS USA, Inc.

Manager, Consumer Relations

P O Box 1976

Indianapolis, IN 46206

Attach your sales receipt to the booklet for future reference

or jot down the date this product was purchased or

received as a gift. This information will be valuable if

service should be required during the warranty period.

Purchase date__________ Name of store__________________

NOTE: The RBRC seal on the battery

used in your ATLINKS USA, Inc.

product indicates that we are

participating in a program to collect

and recycle Nickel Cadmium batteries

throughout the United States. Please

call 1-800-8-BATTERY for information

or contact your local recycling center.

INTERFERENCE INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference; and (2) This device must accept any

interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna (that is, the antenna

for radio or television that is “receiving” the interference).

• Reorient or relocate and increase the separation between the

telecommunications equipment and receiving antenna.

• Connect the telecommunications equipment into an outlet on a circuit

different from that to which the receiving antenna is connected.

• Consult the dealer or an experienced radio/TV technician for help.

If these measures do not eliminate the interference, please consult

your dealer or an experienced radio/television technician for

additional suggestions. Also, the Federal Communications

Commission has prepared a helpful booklet, “How To Identify and

Resolve Radio/TV Interference Problems.” This booklet is available

from the U.S. Government Printing Office, Washington, D.C. 20402.

Please specify stock number 004-000-00345-4 when ordering copies.

LIMITED WARRANTY

What your warranty covers:

• Defects in materials or workmanship.

For how long after your purchase:

• One year, from date of purchase.

(The warranty period for rental units begins with the first rental or 45 days from

date of shipment to the rental firm, whichever comes first.)

What we will do:

• Provide you with a new or, at our option, a refurbished unit.

• The exchange unit is under warranty for the remainder of the original

product’s warranty period.

How to make a warranty claim:

• Properly pack your unit. Include any cables, etc., which were originally

provided with the product. We recommend using the original carton and

packing materials.

• ”Proof of purchase in the form of a bill of sale or receipted invoice which is

evidence that the product is within the warranty period, must be presented to

obtain warranty service.” Also print your name and address and a description

of the defect. Send via standard UPS or its equivalent to:

ATLINKS USA, Inc. c/o Thomson multimedia Inc.

11721 B Alameda Ave.

Socorro, Texas 79927

• Pay any charges billed to you by the Exchange Center for service not

covered by the warranty.

• Insure your shipment for loss or damage. Thomson multimedia Inc.

accepts no liability in case of damage or loss en route to Thomson

multimedia Inc..

• A new or refurbished unit will be shipped to you freight prepaid.

What your warranty

does not

cover:

• Customer instruction. (Your Owner’s Manual provides information regarding

operating instructions and user controls. Any additional information, should

be obtained from your dealer.)

• Installation and setup service adjustments.

• Batteries.

• Damage from misuse or neglect.

• Products which have been modified or incorporated into other products.

• Products purchased or serviced outside the USA.

• Acts of nature, such as but not limited to lightning damage.

Product Registration:

• Please complete and mail the Product Registration Card packed with your

unit. It will make it easier to contact, you should it ever be necessary. The

return of the card is not required for warranty coverage.

Limitation of Warranty:

• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO

THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED

(INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR

WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., IT’S AGENTS, OR

EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE

SCOPE OF THIS WARRANTY.

• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE

EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC. SHALL NOT

BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING

FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF

ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS

DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED

BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT

PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS

PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET

FORTH ABOVE.

How state law relates to this warranty:

• Some states do not allow the exclusion no limitation of incidental or

consequential damage, or limitation on how long an implied warranty

lasts so the above limitations or exclusions may not apply to you.

• This warranty gives you specific legal rights, and you may have other

rights which vary from state to state.

If you purchased your product outside the USA:

• This warranty does not apply. Contact your dealer for warranty

information.

ACCESSORY ORDER FORM

(OR CALL 1-800-338-0376 FOR ACCESSORIES ONLY)

CUSTOMER: CUT ALONG DOTTED LINE.

✂

*Prices are subject to change without notice.

Total Merchandise.........................................$_______________

Sales Tax........................................................$_______________

We are required by law to collect the appropriate sales tax for each individual state,

county, and locality to which the merchandise is being sent. Duties will apply for

shipments to Canada.

Use VISA or Master Card or Discover preferably. Money order or check must be in U.S.

currency only. No COD or Cash. All accessories are subject to availability. Where

applicable, we will ship a superseding model.

Shipping/Handling....................................... $_______________

Total Amount Enclosed.................................$_______________

Mail order form and money order or check (in U.S. currency)

made payable to Thomson multimedia Inc. to:

Thomson multimedia Inc.

Mail Order Department

P.O. Box 8419

Ronks, PA 17573-8419

Name_______________________________________________________

Address_____________________________________ Apt.____________

City ________________________State________ ZIP_________________

Daytime Phone Number ( )_______________________________

Please make sure that this form has been filled out completely.

____________________________________________________________________

Authorized Signature

My card expires:

Copy the number above your

name on the Master Card

For credit card purchases

Your complete charge card number, its expiration date and your

signature are necessary to process all charge card orders.

Copy your complete account number from your VISA card.

My card expires:

Copy your complete account number from your

Master Card or Discover.

$5.00

DESCRIPTION

CATALOG NO.

TOTAL

QTY.

PRICE*

Belt clip

5-2462

$4.95

Headset

5-2425

$36.35

5-2461

$14.95

Replacement battery

5-2463

5-2444

(white)

(black)

HEADSET

Headset

jack

Headset

plug

Slot for

belt clip

Slot for

belt clip

1 2

Comments to this Manuals

No comments

RCA 26930 User Manual Page 2

Comments to this Manuals

Related products and manuals for Telephones RCA 26930