RCA F27450 User Manual Page 4

  • Download
  • Add to my manuals
  • Print
  • Page
    / 64
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 3
2 Chapter 1
Chapter 1: Connections & Setup
Things to Consider Before You Connect
Protect Against Power Surges
Connect all components before you plug any of their power cords into the wall outlet.
Turn off the TV and/or component before you connect or disconnect any cables.
Make sure all antennas and cables are properly grounded. Refer to the Important Safeguards sheet packed
with your TV.
Protect Components from Overheating
Dont block ventilation holes on any of the components. Arrange the components so that air can circulate
freely.
Dont stack components.
When you place components in a stand, make sure you allow adequate ventilation.
If you connect an audio receiver or amplifier, place it on the top shelf so the heated air from it wont flow
around other components.
Position Cables Properly to Avoid Audio Interference
Insert each cable firmly into the designated jack.
If you place components above the TV, route all cables down the side of the back of the TV instead of
straight down the middle of the back of the TV.
If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin lead cables
away from audio/video cables.
Important Stand and Base Safety Information
Choose the location for your TV carefully. Place the TV on a stand or base that is of adequate size and strength
to prevent the TV from being accidentally tipped over, pushed off, or pulled off. This could cause personal
injury and/or damage the TV. Refer to the Important Safeguards sheet packed with your TV.
Use Indirect Light
Dont place the TV where sunlight or room lighting will be directed toward the screen. Use soft or indirect
lighting.
Connection Pictures
Audio/video cables are usually bundled together. For better visibility, the connection pictures in this book
show each cable separately (audio left, audio right, and video).
DEMO PIN
T
h
i
s
D
e
m
o
P
i
n
a
c
t
i
v
a
t
e
s
a
n
a
u
t
o
m
a
t
i
c
G
U
I
D
E
P
l
u
s
+
d
e
m
o
.
R
E
T
A
I
L
E
R
S
;
D
o
N
O
T
r
e
m
o
v
e
t
h
i
s
D
e
m
o
P
i
n
.
R
e
m
o
v
a
l
w
i
l
l
d
i
s
a
b
l
e
t
h
e
a
u
t
o
m
a
t
i
c
d
e
m
o
.
C
O
N
S
U
M
E
R
S
:
R
E
M
O
V
E
t
h
i
s
D
e
m
o
P
i
n
a
n
d
i
n
s
e
r
t
t
h
e
G
-
L
i
n
k
c
a
b
l
e
h
e
r
e
b
e
f
o
r
e
u
s
i
n
g
t
h
i
s
T
V
.
Demo Pin
You must remove the Demo Pin from the G-LINK jack on the back of your TV in order
for your TV to operate properly and to connect the G-LINK cable.
Put Batteries in the Remote
1. Remove the battery compartment cover on the remote.
2. Insert new batteries. Match the polarities (+ and -) on the batteries with the
diagram on the remote.
3. Put the battery compartment cover back on the remote.
Page view 3
1 2 3 4 5 6 7 8 9 ... 63 64

Comments to this Manuals

No comments